orphan: true


Dexcom G6 and ONE

Ön Bilgi

  • Follow general CGM hygiene and setting sensor recommendation here.

General hints for looping with G6 and ONE

  • Recent transmitters are called Firefly. Sensors cannot be restarted without removing the transmitter, which itself cannot be reset, they also do not generate raw data.

  • If you are restarting sensors, ensure you are ready to calibrate and keep an eye on variation.

  • Pre-soaking of the G6/ONE with factory calibration is likely to give variation in results. ‘pre-soak’ ön ısınma yapıyorsanız, en iyi sonuçları almak için muhtemelen sensörü kalibre etmeniz gerekecektir.

Read more in the article published by Tim Street at www.diabettech.com.

If using G6 or ONE with xDrip+

  • If you are using a recent (Firefly) transmitter, preemptive restarts are ignored.

  • If you are using a modded transmitter you do not need to use preemptive restarts.

  • If you are using an old rebatteried transmitter, the safest thing to do is disable preemptive restarts. Though, in this case you will have to use the G6 in non-native mode (which is unadvisable as it disables factory calibration and doesn’t filter noisy readings), or else the sensor will stop after 10 days.

  • The Dexcom G6 and ONE transmitters can simultaneously be connected to the Dexcom receiver (or alternatively the t:slim pump) and one app on your phone.

  • When using xDrip+ as receiver uninstall the Dexcom app first. You cannot connect xDrip+ and Dexcom app with the transmitter at the same time!

  • If you need Clarity and want to profit from xDrip+ alarms use the BYODA (only G6) with local broadcast to xDrip+.

  • You can also use xDrip+ as a companion app of the official Dexcom app, but you might experience delays in BG readings.

  • If not already set up, download xDrip+ and follow the instructions on xDrip+ settings page.

  • Select xDrip+ in in ConfigBuilder, BG Source.

  • Adjust settings in xDrip+ according to xDrip+ settings page

Kendi Dexcom Uygulamanızı Oluşturun ile G6 kullanıyorsanız

BYODA broadcast options

  • Bu uygulama, Dexcom G6’nızı herhangi bir Android akıllı telefonla kullanmanızı sağlar.

  • Uninstall the original Dexcom app or patched Dexcom app if you used one of those previously (do not stop the currently running sensor)

  • Install the downloaded apk

  • Yamalı uygulamada sensör kodunu ve verici seri numarasını girin.

  • In phone settings go to apps > Dexcom G6 > permissions > additional permissions and press ‘Access Dexcom app’.

  • Kısa bir süre sonra BYODA verici sinyalini almalıdır.

Settings for AAPS

  • Select ‘Dexcom App (patched)’ in in ConfigBuilder, BG Source.

  • If you don’t receive any values select any other data source, then re-select ‘Dexcom App (patched)’ to trigger the demand for permissions to establish the connection between AAPS and BYODA-broadcast.

xDrip+ için ayarlar

  • Veri kaynağı olarak ‘640G/Everses’i seçin.

  • Command ‘start sensor’ must be performed in xDrip+ in order to receive values. This will not affect your current sensor controlled by Build Your Own Dexcom App.

Troubleshooting G6 and ONE

Dexcom G6/ONE specific troubleshooting

  • Scroll down to Troubleshooting here.

Genel sorun giderme

General Troubleshooting for CGMs can be found here.

Çalışan sensörle yeni verici

If you happen to change transmitter during a running sensor session you might try to remove the transmitter without damaging the sensor mount. A video can be found here. If you opt for this solution instead, you must be careful to avoid damaging sensor contacts with the strip.